RØDE Central에서 라우팅 모드 구성

Wireless PRO 수신기를 컴퓨터나 휴대폰에 연결한 상태에서 'Routing' 메뉴를 클릭하면 사용 가능한 모든 라우팅 모드(활성화된 경우 타임코드 모드 포함)를 선택할 수 있습니다. 자세한 내용은 '라우팅 모드' 섹션을 참조하십시오.

Configuring Camera Presets in RØDE Central

In RØDE Central, you can select from a list of presets for a wide range a popular camera models. These presets automatically set the gain levels of your Wireless PRO's output to best match the camera you’re using it with.

To access these presets, connect your Wireless PRO receiver to your computer and open RØDE Central (desktop). Click ‘Gain Mode’ and select 'Preset’ with the camera icon. Now you can click the next button labelled ‘Preset’, click the ‘+’ button, and select the manufacturer and model of camera you are using.

On the next screen, you’ll find a link to a guide on setting up your camera’s audio settings for optimal use with the Wireless PRO. Once you’ve followed these instructions, click ‘Add’ to load the preset onto your Wireless PRO. Repeat the process to add other presets (up to 10) for any other cameras you’ll be using with your Wireless PRO.

Configuring Backlight and LED Dimming

The Wireless PRO receiver’s screen features a backlight that you can set to automatically dim after 10 seconds of inactivity. To enable this, connect your receiver to a computer or phone, open RØDE Central, then toggle the ‘Dim (Backlight)’ setting to ‘Auto’. Toggle it to ‘Off’ to disable automatic dimming.

You can also adjust the transmitter’s LED brightness if you want a more discreet aesthetic. With your transmitter(s) connected to a phone or computer running RØDE Central, click the ‘LEDs’ toggle to switch between ‘Bright’ and ‘Dim’.

Configuring the Ø Button

Both the transmitters and receiver feature a Ø button, which when long-pressed functions as a power on and off for that unit, but you can also configure each button to perform a variety of short-press functions.

Receiver (RX)

• Marker – places a marker in the on-board recordings of both transmitters.
• Record – starts or stops on-board recording for both transmitters simultaneously.

Transmitter (TX)

• Marker – places a marker in the on-board recording of just the transmitter on which you press the button.
• Mute – mutes the signal being sent from the transmitter to the receiver (but doesn’t affect on-board recording).

High-Pass Filters

The Wireless PRO features a two-stage high-pass filter for each of its transmitters. A high-pass filter, also known as a ‘low-cut’, removes lower frequencies in an audio signal, which can be useful for adding clarity to your audio and helping to tame any rumble caused by wind noise.

With your transmitter connected to RØDE Central, you can toggle the filter between 75Hz, 100Hz and off for each transmitter. These filters apply to both the transmitter’s in-built microphone and any connected external microphone, such as the included Lavalier II.

RØDE Central로 Wireless PRO 펌웨어 업데이트

Wireless PRO의 펌웨어를 업데이트하려면, 수신기와 두 송신기를 충전 케이스에 넣고 컴퓨터 또는 휴대폰에 연결한 후 RØDE Central을 엽니다. Wireless PRO 또는 충전 케이스에 새 펌웨어 버전을 사용할 수 있는 경우 업데이트하라는 메시지가 표시됩니다. 'Update All'를 클릭하여 프로세스를 시작하고 지시를 따르기만 하면 됩니다.

참고: 업데이트 프로세스를 시작하려면 Wireless PRO 송신기 및 수신기의 배터리가 15% 이상 남아 있어야 합니다. 모바일 버전의 Central을 사용하여 충전 케이스 펌웨어를 업데이트할 수 없습니다.